Wandres Applications

Wandres develops and manufactures cleaning systems for a great variety of cleaning applications in the following industry sectors:-

Furniture parts and panels. Removal of fine dust and particles before assembly, painting, stacking, packing etc.

Cleaning and ProcessingCleaning after edge processing. 

Normally, panels are machined at the edges right after the converting process. It is recommendable to clean the surfaces before inspection and before stacking from above and from below.

 

Cleaning after sawingCleaning after sawing

During the laminate production, the edge processing will generate a large quantity of fine and very hard dust particles. When the panels are transported over longer distances, these particles will scratch the surface

 

claening before stackingCleaning before stacking

Dirty suction cups, turning cones etc lead to surface errors and scratches. Sword Brushes will provide for clean surfaces and will avoid that particles are dragged on to subsequent processes.

.

Cleaning before lacqueringCleaning before lacquering

High-end furniture front panels are often lacquered. In order to guarantee high quality surfaces without particle inclusions, it is imperative to clean the panels first.

 

Cleaning after sandingCleaning after sanding

Technically, it is very challenging to clean pre-lacquered, ground surfaces. The Sword Brush effectively cleans coarse particles and very fine dusts.

 

cleaning of drill holes and groovesCleaning of drill holes and grooves

Particles in drill holes and grooves will lead to all kinds of production interference’s no matter whether they occur before camera inspection or before the stacking, lacquering etc. processes.

 


Blanks

Cleaning of blanks for body skin components and tailored blanks before forming

blanks header

Surface Cleaning of Blanks

cleaning after punchingCleaning after punching

Punching processes cause particles that will later lead to production interferences. Especially pressed screens that will later serve to conduct electrical currents are susceptible to these interferences (short circuits) and need to be free from particles.

 

Cleaning after laser cuttingCleaning after laser cutting

Blanks for skin body components need to be cleaned from both sides after the laser cutting process. The Cleaner CF cleans blanks up to a width of 3200 mm.

 

cleaning before bendingCleaning before bending

Especially metal parts generate furrows in the bending area on high-end optical surfaces. There will be subsequent errors if the particles adhere to the surfaces of the tools.

.

claening after sandingCleaning after sanding

Sanding dust on product surfaces lead to all kinds of problems during subsequent processes such as the application of a protective foil. The Sword Brush uses the patented Ingromat® system to effectively remove particles and very fine dusts from the surfaces.

.

cleaning after cuttingCleaning after cutting

Cutting processes always generate particles. High-end blanks, e.g. for body skin components, should therefore always been cleaned.

.

.

Cleaning before mouldingCleaning before moulding

Particles on blanks cause surface errors during the deep-drawing and the moulding processes. The Evomat Cleaner EVO cleans blank surfaces up to a transport speed of 180 m/min.

.


Coils | Double-sided cleaning of metal coils (stainless steel, aluminium, copper etc.)

Coils | Double-sided cleaning of metal coils (stainless steel, aluminium, copper etc.)

Surface Cleaning of Blanks

cleaning after punchingCleaning after punching

Punching processes cause particles that will later lead to production interferences. Especially pressed screens that will later serve to conduct electrical currents are susceptible to these interferences (short circuits) and need to be free from particles.

.

 

Cleabing after laser cuttingCleaning after laser cutting

Blanks for skin body components need to be cleaned from both sides after the laser cutting process. The Cleaner CF cleans blanks up to a width of 3200 mm.

.

cleaning before bendingCleaning before bending

Especially metal parts generate furrows in the bending area on high-end optical surfaces. There will be subsequent errors if the particles adhere to the surfaces of the tools.

.

claening after sandingCleaning after sanding

Sanding dust on product surfaces lead to all kinds of problems during subsequent processes such as the application of a protective foil. The Sword Brush uses the patented Ingromat® system to effectively remove particles and very fine dusts from the surfaces.

.

cleaning after cuttingCleaning after cutting

Cutting processes always generate particles. High-end blanks, e.g. for body skin components, should therefore always been cleaned.

.

.

Cleaning before mouldingCleaning before moulding

Particles on blanks cause surface errors during the deep-drawing and the moulding processes. The Evomat Cleaner EVO cleans blank surfaces up to a transport speed of 180 m/min.

.


Coils

Double-sided cleaning of metal coils (stainless steel, aluminium, copper etc.)

coil-header

Cleaning after heat treatment (furnaceCleaning after heat treatment (furnace)

Stainless steel coils are cleaned from above and from below after the furnace to remove abrasions or deposits that originate in the annealing process. Very often, two rubber rollers are installed from above and from below at the infeed and at the outfeed of the cleaning modules to appease the coil that sometimes may be very wavy. The Cevomat Cleaner may effectively clean even sharp-edged metal coils.

.

Cleaning after sandingCleaning after sanding

Dust from sanding processes will lead to many errors in subsequent processes, i.e. the application of protective foils. A Wandres Sword Brush will effectively remove particles and very fine dusts from the surfaces by using the patented Ingromat® system.

.

Cleaning of rollersCleaning of rollers

Adhesive dust particles and other kinds of deposits on rollers cause these particles to be dragged on to other processes and produce surface errors on the material surface. In order to avoid this phenomenon Sword Brushes are installed to clean cylindrical steel rollers, rubber rollers or profiled rollers.

.

Cleaning before calender mill standCleaning before calender mill stand

Large metal coils need to be cleaned from above and from below before the skin pass mill or before the levelling rollers. Rubber rollers are often installed at the infeed and the outfeed of the Cevomat Cleaner to guarantee a smooth transition between the end of one coil and the beginning of the next coil.

.

Cleaning before levelling rollersCleaning before leveling rollers

Metal coils that are unwound, normally have to be straightened. Leveling rollers need to be free from particles, otherwise there will be marks on the surfaces or the surfaces will be damaged. The coil that comes from the reel is appeased with rollers and will then pass onto the Sword Brushes that will clean